Skip to Content
For all your Air Conditioning & Appliance needs!
​

352-726-7530

Locations

Wishlist

Cart

Speed Queen Washer Er, OF

Fri Feb 24 2023

  • Error Codes

Speed Queen Washer Er, OF Error Code: What It Means & What to Check

If your Speed Queen washer displays Er, OF, it’s an overflow error. That means the washer sensed an unsafe high water level and/or it couldn’t lower the water level by draining within the allowed time. This is one you should take seriously, because it can lead to floor damage fast.

Q: What does Er, OF mean on a Speed Queen washer?

A: Er, OF is an overflow condition. Speed Queen’s guide explains the control was not able to lower the water level within 5 minutes. Common suspects include a leaky inlet (water) valve or a pressure hose problem (blockage or air leak). Power must be cycled off to clear the error. :contentReference[oaicite:1]{index=1}

Safety First

  • Stop the water: Turn off the hot and cold water valves at the wall immediately if water is still filling.
  • Unplug the washer if there’s standing water or any risk of water reaching electrical parts.
  • Keep towels handy and avoid running more loads until the cause is identified.

Symptoms You May Notice

  • Washer appears to overfill or water level gets higher than normal
  • Washer tries to drain but the water level doesn’t drop as expected
  • Water in the tub when the cycle stops
  • Water on the floor or in the drip pan (if you have one)

Quick Checks You Can Do Now

  1. Power down to clear: Turn the washer off and unplug (or flip the breaker) for 60 seconds, then restore power. (If it immediately refills/overfills again, shut water valves back off.) :contentReference[oaicite:2]{index=2}
  2. Confirm the washer is actually draining: If you start a drain/spin, listen for draining and verify the standpipe/sink drain can accept water without backing up.
  3. Check for a slow “valve seep”: With the washer OFF, watch the tub for a few minutes. If water slowly creeps in, the inlet valve may be leaking internally.
  4. Inspect hose connections: Make sure hot/cold fill hoses are snug and not leaking at the wall or washer.
  5. Don’t push the drain hose too far down: A bad drain setup can create odd water behavior. Ensure the hose is secured and the standpipe has proper air gap space.

Tip: Speed Queen specifically calls out checking the inlet (water) valve and the pressure hose for blockage or air leaks as likely causes. :contentReference[oaicite:3]{index=3}

Common Causes (and Likely Parts)

  • Leaky inlet (water) valve allowing continued filling :contentReference[oaicite:4]{index=4}
  • Pressure hose blockage (washer can’t “read” the correct water level) :contentReference[oaicite:5]{index=5}
  • Air leak in the pressure hose (inaccurate level sensing) :contentReference[oaicite:6]{index=6}
  • Drain issue preventing the washer from lowering the water level (restriction, pump trouble, or drain plumbing problem)

Parts that are commonly involved

  • Inlet (water) valve / mixing valve
  • Pressure hose (and its connections)
  • Drain pump / drain path components (if it won’t lower level by draining)

When to Call Beacon

If Er, OF returns, if you see any active overfilling, or if the washer can’t lower the water level, schedule service. Beacon’s friendly technicians in yellow can quickly identify whether the culprit is the inlet valve, pressure hose, or a drain-side failure—and help prevent water damage.

Content Update & Editorial Review

Reviewed for accuracy and clarity on by Chris. Meet our authors.

FAQ: Speed Queen Washer Er, OF

Is Er, OF always a drain pump problem?

Not always. It can be a true overflow/filling problem (like a leaky inlet valve) or a level-sensing issue (pressure hose), and it can also happen if the washer can’t lower the level by draining in time. :contentReference[oaicite:7]{index=7}

What should I do first if the tub is still filling?

Turn off the hot and cold water valves at the wall immediately. Then unplug the washer if water is present where it could reach electrical components.

Can a leaky inlet valve cause Er, OF?

Yes. Speed Queen’s guide lists a leaky water valve as a likely cause. :contentReference[oaicite:8]{index=8}

Why does the pressure hose matter?

The pressure hose helps the washer sense the water level. If it’s blocked or leaking air, the control can get a false reading and trigger overflow-related errors. :contentReference[oaicite:9]{index=9}

How do I clear the code?

Speed Queen notes the machine must be powered down to clear the error. If it comes back, the underlying cause still needs to be corrected. :contentReference[oaicite:10]{index=10}

When should I call Beacon?

If Er, OF returns, if the washer overfills again, or if it can’t lower the water level, schedule service so our friendly technicians in yellow can diagnose it safely.

Related Articles