Skip to Content
For all your Air Conditioning & Appliance needs!
​

352-726-7530

Locations

Wishlist

Cart

Speed Queen Washer Er, NF

Fri Feb 24 2023

  • Error Codes

Speed Queen Washer Er, NF Error Code: What It Means & What to Check

If your Speed Queen washer is showing Er, NF, it’s a no-fill / not-filling type error. The washer started a fill, but it didn’t sense the water level rising enough early in the fill. That’s usually a water supply issue (valves off, kinked hoses, clogged screens), but it can also be an inlet valve or water-level sensing problem.

Q: What does Er, NF mean on a Speed Queen washer?

A: Er, NF means the washer did not fill to the proper level—there was no or very little change in water level sensed within the first few minutes of filling. Start by confirming both water valves are on, hoses aren’t kinked, and inlet screens are clean. :contentReference[oaicite:1]{index=1}

What You Might Notice

  • Washer stops early and displays Er, NF
  • Very slow fill or little/no water entering the tub
  • You hear a trickle instead of a steady fill
  • Hot fills but cold doesn’t (or vice versa)

Safety First

  • Before moving the washer to check hoses, unplug the washer.
  • Turn off water at the wall valves if you need to remove hoses.
  • Don’t overtighten connections—snug is enough to avoid cracking fittings.

Quick Checks You Can Do Now

  1. Confirm both faucets are fully ON: Hot and cold should be open all the way. :contentReference[oaicite:2]{index=2}
  2. Check for kinked or pinched hoses: Make sure the fill hoses aren’t twisted behind the washer. :contentReference[oaicite:3]{index=3}
  3. Clean inlet screens: Shut off water, disconnect hoses, and clean the small screens at the washer’s mixing valve/inlet and at the faucet end of the hoses. :contentReference[oaicite:4]{index=4}
  4. Quick reset to clear the code: Unplug the washer for about 15 seconds, then plug back in and retry. :contentReference[oaicite:5]{index=5}
  5. Verify water pressure/flow: If the home has very low pressure, the washer may not see the water level rise fast enough (especially if multiple fixtures are running).
  6. Try a different temperature setting: If the code appears only on HOT or only on COLD, that points to a single supply valve/line/screen issue.

Tip: If this started right after plumbing work, a moved/kinked hose or debris in the inlet screens is extremely common.

Common Causes (and Likely Parts)

  • Water valves partially closed or supply turned off
  • Kinked fill hose restricting flow
  • Clogged inlet screens at the mixing valve or hose ends :contentReference[oaicite:6]{index=6}
  • Inlet (water) valve not opening properly
  • Water level/pressure sensing issue (less common, usually after supply checks)

When to Call Beacon

If Er, NF returns after you’ve confirmed both faucets are on, hoses are clear, and inlet screens are cleaned, it’s time for diagnosis. Beacon’s friendly technicians in yellow can test water flow, confirm valve operation, and verify the washer’s water-level sensing so you can get back to reliable cycles.

Content Update & Editorial Review

Reviewed for accuracy and clarity on by Chris. Meet our authors.

FAQ: Speed Queen Washer Er, NF

Does Er, NF mean there’s no water at all?

Not always. It can also mean the washer is filling too slowly and doesn’t sense enough level change early in the fill. :contentReference[oaicite:7]{index=7}

What’s the fastest thing to check first?

Make sure both HOT and COLD wall valves are fully open and the hoses aren’t kinked behind the washer. :contentReference[oaicite:8]{index=8}

Why does cleaning inlet screens matter?

Those screens catch debris from plumbing. When they clog, flow drops and the washer may not reach the expected water level in time. :contentReference[oaicite:9]{index=9}

How do I clear the Er, NF code?

Speed Queen’s guidance is to unplug the machine for about 15 seconds to clear the code, then retry after checking water supply basics. :contentReference[oaicite:10]{index=10}

If only HOT (or only COLD) fails, what does that point to?

Often a single water valve turned off, a kinked hose, or a clogged screen on that side. It can also indicate an inlet valve issue affecting one side more than the other.

When should I call Beacon?

If Er, NF keeps returning after valves/hoses/screens are confirmed, schedule service so our friendly technicians in yellow can diagnose the inlet valve or water-level sensing safely.

Related Articles