Skip to Content

Speed Queen Washer Er, LE

Fri Feb 24 2023

  • Error Codes

Speed Queen Washer Er, LE Error Code: What It Means & What to Check

If your Speed Queen washer is showing Er, LE, it’s a water leak detection error. In plain English: during a leak-check step, the washer senses the water level dropping when it shouldn’t. That can happen from an actual leak, a slow drain/siphon condition, or a valve/connection that’s not behaving normally.

Q: What does Er, LE mean on a Speed Queen washer?

A: Er, LE means the washer detected a water level drop during the leak detection step (if enabled). Speed Queen’s guide points to checking the mixing valve for leaks. If the code returns after basic checks, service is recommended.

Symptoms You May Notice

  • Er, LE appears during a cycle or shortly after fill
  • Water under/around the washer
  • Washer seems to lose water level unexpectedly
  • Intermittent code that returns on certain cycles

Safety First

  • If you see water near electrical parts, unplug the washer before wiping or inspecting closely.
  • Use towels and a flashlight—avoid opening panels unless you’re qualified.
  • If there’s active leaking, stop the cycle and shut off the wall water valves.

Quick Checks You Can Do Now

  1. Look for obvious leaks: Check the floor under the washer, behind it, and around the front corners for fresh water tracks.
  2. Check the fill hoses and connections: Confirm both hot/cold hoses are snug at the wall and at the washer (no drips).
  3. Inspect the mixing valve area (rear water inlet): Look for slow dripping where water enters the washer. Speed Queen specifically recommends checking the mixing valve for leaks.
  4. Rule out drain siphoning: Make sure the drain hose is secured and not shoved too far down the standpipe. If the hose sits too low or is sealed tight in the pipe, it can siphon water out and “drop the level.”
  5. Check the standpipe/drain for slow backing up: If water backs up, it can cause odd drain behavior and water movement that trips errors.
  6. Reset and retest: Power the washer off, wait 30–60 seconds, then run a short test cycle and watch for any drips during fill and agitation.

Tip: If you only see Er, LE on higher-fill cycles, pay extra attention to hose connections, the inlet/mixing valve area, and drain hose setup.

Common Causes (and Likely Parts)

  • Leak at the mixing valve / inlet area (water entering the washer)
  • Loose or worn fill hoses or hose washers
  • Drain siphoning due to drain hose height/standpipe setup
  • Internal leak (tub-to-pump hose, pump area, seals) — requires service
  • Water valve not sealing (minor seep/drip) or related control/wiring issue

When to Call Beacon

If Er, LE returns after you’ve checked for visible leaks and confirmed the drain hose isn’t siphoning, it’s time to schedule service. Beacon’s friendly technicians in yellow can pinpoint whether the issue is the inlet/mixing valve, an internal hose/pump leak, or a related sensing/control problem—before it causes floor damage.

Content Update & Editorial Review

Reviewed for accuracy and clarity on by Chris. Meet our authors.

FAQ: Speed Queen Washer Er, LE

Does Er, LE always mean there’s a big leak?

Not always. It means the washer sensed the water level dropping during a leak-check step. That can be a small drip, a siphoning drain setup, or an internal leak.

What’s the first place to check?

Start at the rear inlet/mixing valve area and hose connections. Speed Queen’s guide specifically mentions checking the mixing valve for leaks.

How can the drain hose cause a “leak” error?

If the drain hose is too low or sealed tightly in the standpipe, it can siphon water out of the tub—making the washer think it’s losing water unexpectedly.

Should I keep running loads if I see water on the floor?

No. Stop the cycle, shut off water to the washer, and schedule service. Continued leaking can damage flooring and cabinets fast.

Could a water valve cause Er, LE?

It can. A valve or inlet/mixing area leak can show up as water loss or water where it shouldn’t be—especially during fill steps.

When should I call Beacon?

If Er, LE returns after basic leak checks and confirming the drain hose setup, schedule service so our friendly technicians in yellow can locate the leak source safely.

Related Articles