Speed Queen Washer Ed, 10 Error Code: What It Means & What to Check
Q: My Speed Queen washer is showing Ed, 10. What does it mean, and what should I check?
A: On many Speed Queen washers, Ed, 10 is an input voltage select error. In plain English: the washer detected a problem with how it’s identifying (or expecting) the incoming electrical supply. This can happen after a power event, if there’s unstable voltage, if the washer is plugged into an improper outlet setup, or if there’s a control/connection issue that affects the washer’s voltage-detection logic.
Because this is power-related, the goal is to make sure the washer is on a stable, proper outlet and rule out simple causes before calling our friendly technicians in yellow.
What you might notice
- The washer won’t start and displays Ed, 10
- The code appears after a storm, outage, or power flicker
- The display resets or flickers
- Other electronics in the home reboot or lights dim at times
Safety first
- If you smell burning, see scorch marks, or the outlet feels hot, stop using the washer and get help right away.
- Do not use extension cords or power strips.
- Unplug the washer before inspecting the cord/outlet area.
Step-by-step quick checks (safe homeowner checks)
1) Power reset (most common first step)
- Press Power to stop/clear the display.
- Unplug the washer for 2 minutes.
- Plug it back in and see if the code clears.
2) Make sure the washer is plugged directly into the wall
- Plug the washer directly into a proper, grounded laundry outlet.
- Avoid power strips, extension cords, or outlet adapters—these can cause voltage drop and detection errors.
3) Check plug/outlet fit
- Make sure the plug is fully seated.
- If the plug feels loose or the outlet looks worn, that can cause intermittent voltage problems.
4) Check for a tripped breaker or GFCI
- If the washer has no power at all, check your breaker panel for a tripped breaker.
- If the laundry circuit is GFCI-protected, check and reset the GFCI (if present).
5) Reduce electrical load on the circuit
- Try running the washer when other high-draw items aren’t running on the same circuit.
- If lights dim when the washer starts, that can point to voltage sag.
6) If you have another proper laundry outlet available, test it
- If the code disappears on a different outlet, the original outlet/circuit may be the problem.
- If the code follows the washer to a different outlet, it points more toward a washer-side detection/control issue.
7) Note when it happens
- Right on power-up? Right when you press Start? During spin?
- After storms/outages?
- This timeline helps our friendly technicians in yellow narrow it down quickly.
Common causes (and likely parts)
- Power event (outage, flicker, voltage dip/brownout)
- Improper outlet setup or loose/worn receptacle causing unstable voltage
- Shared/overloaded circuit creating voltage sag under load
- Home electrical issue (breaker, wiring connection, panel issue)
- Control board / power detection circuit issue in the washer (less common, after outlet/circuit is ruled out)
- Wiring/connector issue inside the washer affecting voltage detection (service-level)
When to call Beacon
If Ed, 10 comes back after a reset and you’ve confirmed the washer is on a stable, proper outlet, call our friendly technicians in yellow. We can check the washer’s power detection, confirm there’s no internal connection issue, and help you determine whether the washer needs repair or if an electrician should evaluate the home circuit for low-voltage conditions.
Request service online or call (352) 726-7530. You can also visit www.BeaconSaves.com.
Content Update & Editorial Review
Date: February 21, 2026
Reviewed by: Chris
Frequently Asked Questions
Is Ed, 10 the same as PF?
They’re related to power, but not identical. PF is a “power fail” record (an interruption). Ed, 10 is a voltage selection/detection issue—meaning the washer isn’t happy with what it’s seeing for input power.
Can a loose outlet cause Ed, 10?
Yes. A loose or worn receptacle can cause intermittent voltage problems that trigger voltage detection errors.
Do I need an electrician?
If you notice dimming lights, repeated breaker trips, hot outlets, or multiple appliances acting odd, an electrician may be appropriate. If only the washer is affected, Beacon can diagnose whether it’s washer-side or power quality.
Should I use a power strip or extension cord?
No. Washers should be plugged directly into a properly rated wall outlet to avoid voltage drop and overheating risks.
Why did this start after a storm?
Storms can cause short voltage dips, flickers, or surges. The washer may detect unstable input conditions and display Ed, 10 as a protective response.
What should I tell Beacon when I call?
Tell us the code (Ed, 10), whether it appears immediately or when starting a cycle, if it began after an outage/storm, and whether you notice lights dimming or other devices rebooting. That helps our friendly technicians in yellow diagnose faster.